MAIN
Cooling System
Previous Page | Next Page
Hello all, Well, I fired her back up today. Put my hand over the oil filler hole, and let it idle. There was no significant vaccuum and no significant air pressure. The valve cover filled about an inch and a half full of oil, with oil coming up the push rod tubes. I'm sure it would have kept going , but I shut it down. As I mentioned earlier, it sounds fine once it gets warmed up. It isn't missing and has good oil pressure. (although the oil gauge doesn't work (Problem #312 of 1067...get to that one later...)... MORE
Well Don May.... The crankcase takes incoming air from the charcoal cannister through a "graduated orifice" feed tube mounted on the valve cover, assuming the valve cover has a non-vented oil filler cap. The "exhaust" side would be the hose coming from the cannister on the timing case cover which vents into the intake system via individual hoses which feed a "graduated orifice" within each carburator. In this instance, while the engine is running, Kevin removed the oil filler cap and noticed no vacuum or pressure. So even though Kevin states the individual hoses to each carb appear pinched,... MORE
Kevin... You engine looks nothing like the engine in the Haynes manual? Hmmm.... Well...a picture is worth a thousand words, Kev. Those hoses to the carburators from the cannister on the timing chain cover should definitely be clear and open.... no doubt about this. If the valve cover was on the engine when you were running it, then with every respect, Kevin, there is no way you could tell where the oil was coming from... the oil filler hole is too small to provide a decent view and through this small hole, not enough light in there...to dark in... MORE
They only go in from 1 side. I found that a hair dryer to heat the plexaglas so it was very hot and then I used a couple of putty knifes/paint scrapers to carefully slide the top edge in the middle of the frames. The putty knives also work well to place the felt in a U shape in the frames. The Bugeye front window doesn't slide. Bob, Troutdale, OR 60 Bugeye "Robert Webb" 25463... MORE
Hi, Bill.... Jegs, Summit or Racer Wholesale offer some nice 4 point systems with 3" webbing that really holds you in. These are usually top brands like Simpson. They sell the mounting kits as well. The Spridget is small inside so get "pull up" types rather than "pull downs" when it comes to the seat belts (it they still offer a choice in this respect) whether you order/use the shoulder belts or not. As you already know....VB, Moss or any of the other usual suspects for the stock OEM type stuff. "Performance shops" also carry generic types that will... MORE
Check to see if the hose from the top of the oil separator canister on front of the timing chain cover to the carburetors is clogged up and if the two small inlet pipes where the hoses connect at the carburetors are not clogged up. Spray a little carburetor cleaner in them. Don "Don May" 25419... MORE
Biff... how did you guys fair the storm. We never lost power at all.... the yard only looks like an early autumn... lots of leaves, no branches down ...nothing. Our pool has an extra two inches of water and that's it. Paul Tegler ptegler@... www.teglerizer.com "ptegler@cablespeed" 25376... MORE
Well it's about time. My 71 MG is back and refurbed. While it was apart for a new clutch disc, why not put a Datsun 5 speed in it? 266 cam, lite lifters, right springs, new shells on the still-standard crank, Cooper S 163 head with rimflows and ported, 45DCOE, and LCB, with a Kenlowe to cut cooling losses. Cooper S dizzy. I want a merit badge for making the Rivergate kit work. It is not easy for one who must follow directions literally. Much more difficult than it needs to be, for me, anyway. I know many listers... MORE
20.14 Exhaust Emission System. The owner or operator of any new motor vehicle or new motor vehicle engine beginning with the model year 1968 equipped with an exhaust emission system shall maintain the exhaust emission system in good operable condition and shall use it at all times that the motor vehicle or motor vehicle engine is operated. The owner or oper- ator of the motor vehicle or motor vehicle engine shall not remove or intentionally make inoperable within the state of Texas the exhaust emission system or any part thereof, except where the purpose of removal of the exhaust... MORE
Don... "Sounds" (excuse the pun:) like you've got a glasspack (free flow) on there, maybe a Thrush or Cherry Bomb. These are "straight thru" designs (as opposed to the "baffled" stock (or Midas/Meineke/ Walker, etc.) system. It may also be the optional "GEX" straight-through type I've see advertised by MiniMania. "Straight thru" design with sound deadening packed around the "open" core allows for perfomance and/or gas economy along with allowing for a cooler running engine due to the easier trip the hot exhaust gases have outbound. allow the engine to run a little cooler as well as the exhaust... MORE
Hello Folks So heres the story Heading to a cars show about 150 miles away Temp out in AM was around 60 to 65 degrees water temp was getting pre hot by the gage I did pull over and there was a little over flow from the expansion tank but not allot. We did abort the trip and headed home but on the way home the temp gage was all the way past the H on the gage but things seam to be running fine, it didn't feel hot on the feet. So I am thinking the gage is... MORE
Dear Listers, After tinkering with my '75 Midget all summer I finally have the beast to some standard of reliability having (knock on wood) cured the lean running problem. My next endeavor is to swap the Stromberg for a pair of SU's and to replace the clutch due to weak springs, I hope. I will probably lighten the flywheel while I'm at it. Since I will be pulling the engine anyway why not address the unsatisfactory gearbox as well. Running 4000 rpm at 65 mph doesn't sound good to me. Unfortunately the 1500 engine doesn't have a nice swap... MORE
When I converted the 65 Midget to negative earth, the only thing that neede d attention was the tach. I just unhooked it. Wiper motor, fan motor, fuel pump, etc. not affected by the swap. Brad "Brad Fornal" 25130... MORE
Don't know. The car was not driven for almost a year and I do not know what all the PO did to it. The guy I bought it from bought it running, drove it home and a couple of times around the block, did some work on the battery pan, put in a new radiator and hoses then got too busy at his job to do more so never took it off the no-op license and let it sit for almost a year, then when he tried to drive before selling it discovered he could not get it into... MORE
You can certainly put a RX7 rotary in a Midget, but you'd better put in the RX7 trans too. There'll be a lot of parts which will have to be fabricated - exhaust, guage hook-ups, cooling, etc, etc, etc. You'll then have a car which will go faster than either the suspension or brakes can safely handle. I'd suggest you just sell the Midget and buy a RX7. "Jeffrey Holmes" 25076... MORE
if he does, you could turn the engine 90 degrees, and then run a drive belt from the engine to the skateboard wheels - think of the power to weight ratio! "David Jacobs" 25074... MORE
Hi All I have the same problem only It is just on the front left side. I changed the flex hose too. I didnt how ever change or rebuild the master cylinder.I am wondering if it could be the brake union. Maybe the slideing part is stuck. Is this possible? This is where I was heading next. Thank you Rick "mtman19552002" 25062... MORE
Gerard is right on the money. Replace the hoses. And consider getting rid of that silicone. Regards, Jeffrey "Jeffrey Holmes" 25058... MORE
Since you don't say anything about flex lines, I'm gonna say that the culprit, What you describe is usually caused by swelling flexible rubber hoses, It can prevent fluid return to the master cylinder. I thunk silicone fluid in old lines can exacerbat the problem too. It will also swell certain types of rubber, so it may be incompatible with your seals in the MC. Gerard "gerardchateau" 25056... MORE
Nigel, Had to re-core mine and it came back painted gloss black and I am sure it wasn't high temp paint. The gloss finish is nice as it cleans up nicely. Rob C 75 Midget-finally running right after Summer is over. robbiesg@... 25055... MORE
So I am motoring down a nice quiet highway at 50MPH and come to a leisurely stop at a traffic light. 30 seconds go by, light turns green and I motor on up to 50 MPH again. AFter about a mile, I detect the distinct smell of burning brakes. Dang, I hope that's not me.... unfortunately it was. SO I pulled over to the side and came to a stop. The brake pedal was hard and would not depress very far. Furthermore, the brakes were not responding very well (nor grabbing). After stopping I noticed the stinky smoke coming... MORE
Hi guys Was thinking about painting my radiator - is there any specific paint this should be done in? ie heat resistant? or is regular cellulose ok? I'm assuming it's original finish was satin black, is that correct? tia Nigel "amukdigiphoto" 25045... MORE
Hi, Nigel.... Yes...there is special paint according to Eastwood Automotive Products @ www.EastwoodCo.com Type "radiator paint" into the "search" box and there you have it! :):) Cap'n. Bob '60 :{) PilotRob@... 25047... MORE
Interesting experiments, Paul. The most simple well-working PCV system I ever had came on the '67 engine 5 main bearing engine which I installed in place of the 3 main bearng which came in my PO'd '64 MGB. Factory PCV valve (rubber diaphragm) intake manifold mounted breathing through the liquid/vapor flame arrestor mounted on the front of the timing case cover with matched vented/filtered oil filler cap. Replaced the diaphragm once and filtered cap once in a while. And introducing a little water into the intake manifold once a year will help keep things clean. There are also a... MORE
If you are certain you are getting enough travel out ot the slave cylinder to disengage your clutch, then the first thing that comes to mind is that your clutch disc is stuck to the flywheel. How long has it been since it was driven and working properly? Was the fluid loss the reason for the failure and was it from sitting to long? Three other posibilities: * First motion shaft is stuck in or has to much friction with the pilot bushing. * Clutch pressure plate spring/s have failed. * Throw out bearing has come off the fork.... MORE
